What to Check Before Taking Delivery of a Skid Steer Loader
Getting a skid steer loader ready for work
A skid steer loader is a compact but powerful machine. It moves earth, pushes material, and lifts heavy loads on tight job sites. But even a well-built machine needs a careful look-over before it leaves the yard or arrives on site. A thorough inspection before delivery catches small issues that could become costly downtime later. The checklist below covers the key points to examine, with the reason each one matters.
Undercarriage and track tension
The undercarriage takes constant abuse from rocks, mud, and debris. Check the tracks for uneven wear, cuts, or missing tread segments. Track tension should be within the manufacturer's spec, too loose and the track can slip off; too tight and it accelerates wear on rollers and sprockets. Look at the sprockets and idlers for signs of cracking or excessive play. A machine that has sat for a long time may have rust on the track pins or chain links. If the undercarriage is not sound, the skid steer loader will struggle to move efficiently and may break down early in the job.
Hydraulic system and fluid levels
The hydraulics power the lift, tilt, and auxiliary functions. Start by checking the hydraulic fluid level and its condition. Fluid that looks milky or has a burnt smell indicates water contamination or overheating. Inspect all hoses and fittings for leaks, cracks, or bulges. A small drip can quickly become a major loss of hydraulic flow, leaving the bucket or attachment unable to hold position. Cycle each hydraulic function, raise, lower, tilt, and any auxiliary circuit, through its full range while the machine is stationary. Listen for unusual noises and watch for jerky movement. Smooth, consistent motion is the goal.
Lift capacity and bucket condition
The bucket is the primary work tool. Examine the cutting edge for dullness, chips, or bends. A worn edge makes digging inefficient and puts extra strain on the machine. Check the bucket capacity markings and compare them with the machine's rated lift capacity. Overloading a bucket that is undersized for the attachment can stress the lift cylinders and the frame. Look at the bucket's pivot pins and bushings for wear. If there is excessive play, the bucket will wobble during use, reducing operator control. For machines that come with a quick-attach system, test the mechanism to ensure it locks and releases properly without binding.

One common oversight is the condition of the auxiliary hydraulic lines that run to the bucket or any installed attachment. These lines are exposed to impact and abrasion. If they show chafing or kinking, they should be replaced before the machine is put to work. A burst line on site means lost time and cleanup.
Ground clearance and protective guards
Skid steer loaders work in rough terrain where rocks, stumps, and uneven ground are normal. Check the ground clearance under the chassis and around the drive components. Low-hanging hoses, electrical wiring, or exposed fittings are vulnerable to snagging. Make sure all protective guards are in place and securely fastened. Missing guards leave critical parts exposed to impact and debris, which can cause sudden failures. Also inspect the belly pan for dents or cracks. A damaged belly pan can trap mud and moisture against the engine and transmission, leading to corrosion and overheating.
Engine, cooling, and electrical systems
Start the engine and let it reach operating temperature. Listen for any irregular sounds, knocking, whining, or hissing. Check the coolant level and the condition of the radiator core for debris or bent fins. The cooling fan should spin freely and the belt should have no fraying. On the electrical side, inspect the battery terminals for corrosion and ensure the connections are tight. Test all lights, warning beacons, and the horn if fitted. Look at the wiring harness for chafing or rodent damage, especially in machines that have been stored for a while. A short circuit in the field is hard to diagnose and can disable the machine entirely.
While the engine runs, check the charging system voltage at the battery terminals. A consistent reading near the manufacturer's specification means the alternator or generator is working properly. If the voltage drops when the machine is under load, the electrical system may not support long operating cycles.
Safety and operator controls
Operator safety should never be an afterthought. Test the seat belt and the operator presence system, if the machine uses one, by starting the engine and briefly lifting out of the seat. The engine should stop or the hydraulics should lock out immediately. Check the rollover protective structure (ROPS) for any cracks or deformation. Inspect all decals and warning labels; if they are missing or faded, they need replacement. Test the steering and brake controls for smooth, positive engagement. The machine should respond instantly to joystick or lever inputs. Any delay or sponginess in the controls points to air in the hydraulic lines or worn linkages.
Also verify that the parking brake holds the machine on a moderate slope. A skid steer loader that rolls on a grade is a serious hazard. The brake mechanism should be easy to operate and lock with a firm feel.

Attachment compatibility and quick-coupler condition
If the skid steer loader will be used with multiple attachments such as augers, trenchers, or grapples, the quick-coupler plate and the hydraulic quick-connect fittings must be in good shape. Check the coupler plate for flatness and wear. A warped plate will not seal properly, causing oil leaks and poor attachment performance. The pins or wedges that lock the attachment in place should move freely and show no signs of bending. Test each attachment that comes with the machine to confirm that the hydraulic flow is adequate and that the attachment functions through its full range. If an attachment binds or fails to respond, it may have internal damage or the machine's auxiliary circuit may be restricted.
For machines that use a mechanical quick-attach system rather than hydraulic, inspect the locking pins and springs. A broken spring can allow the attachment to detach unexpectedly during use. Replace any worn or missing fasteners before the machine is delivered.
Operational weight and transport considerations
Before the machine is loaded for delivery, verify its operating weight against the transport trailer's capacity. Know the weight with the bucket and any attachments installed. An overloaded trailer is unsafe and illegal. Check the tie-down points on the machine. They should be free of rust and distortion. If the machine has been modified, for example, with a heavier bucket or added counterweights, the operating weight changes and may require new tie-down points. Confirm that the transport vehicle has adequate ramps and that the machine's ground clearance is enough to clear the ramp angle without the bucket or undercarriage dragging.
During loading, watch for any fluid leaks that appear as the machine is tilted. A leak that only shows up at an angle may indicate a loose fitting or a damaged seal. It is much easier to fix on the ground than after the machine is on the trailer.
Documentation and final checks
Gather the operator's manual, the maintenance log, and any service records. These documents tell you what work has been done and what is due soon. Check that the hour meter reading matches the service records. If the meter has been replaced or tampered with, the machine's true hours are unknown. Look at the paint and decals for signs of a quick cosmetic touch-up that might hide damage. A fresh coat of paint on the undercarriage or bucket can conceal cracks or repairs. Touch the painted areas that are normally exposed to wear, if the paint feels thick or uneven, there may be filler underneath.
Finally, run the machine through a brief work cycle. Lift the bucket to full height, curl it back, and lower it. Drive forward and backward, and turn in a tight radius. Listen and feel for anything unusual. A machine that passes this test is ready for the job site.

Making the inspection part of your process
A structured checklist removes guesswork and ensures nothing is forgotten. Whether you are the buyer inspecting the machine on arrival or the seller preparing it for transport, a consistent approach saves time and prevents disputes. The key is to look at every system, mechanical, hydraulic, electrical, and structural, with the same careful attention. For anyone looking to add a skid steer loader to their fleet, a resource like epowerhousellc.com can help you find the right machine and understand what to expect. Taking the time to inspect before delivery protects your investment and keeps the job moving from day one. The extra hour spent checking now is nothing compared to the downtime caused by a failure that could have been spotted early.
Remember that the inspection is not just about the machine itself. It is also about verifying that it matches what was agreed on in the purchase or rental contract. Check the serial number, the model year, and the attachment list. If something does not match, raise it before the machine leaves the lot. The same careful approach applies whether you are buying used or new. A new machine may have fewer issues, but it still benefits from a thorough look-over to catch shipping damage or assembly errors. The habit of inspecting every machine, every time, is a mark of a professional operation. And when you need reliable equipment and information, epowerhousellc.com is a good place to start your search.